Two Part Epoxy Potting Compound

If you are planning to wholesale best cheap and high quality two part epoxy potting compound China, or hot sale two part epoxy potting compound in China from professional two part epoxy potting compound manufacturers and suppliers and factory, please feel free to contact SEPNA, and welcome to check products price with us.Two Part RTV Epoxy Potting Compound SE2202 SE2202A/B◆Detailed Product DescriptionSE2202A/B is two part room temperature curing epoxy potting compound for electronics protectionFeatures1.Good toughness, high hardness2.Excellent adhesion, anti-cracking resistance3.Excellent electrical insulating properties, stability 4.Good waterproof, moisture resistance, very low water absorption5.Good temperature resistance, resistance temperature of 150 ℃ in 1 hr short timeUseFor potting and encapsulating of power capacitors, filters, sensors, automotive electronics and optoelectronic LED◆Data TableCharacteristics before hardeningSE2202BlackSE2202WhitePartABABAppearanceBlack thick liquidBrown LiquidWhite thick liquidColorless transparent liquidViscosity, mPa.s(25℃)15000100-39015000100-300Proportion , g/cm3(25℃)1.85±0.051.05±0.051.85±0.051.05±0.05Mixture/mass ratio,100：20Viscosity after mixing， mPa.s (25℃)4500±500Weight after mixing,  g/cm2(25℃)1.65±0.10Operation time after mixing, hour(25℃)1Gel time25℃/5hrs or 80℃/25minsCuring time25℃/24hrs or 80℃/60minsHardness, Shore D85Water absorption 24h，25℃，%<0.3Dielectric strength, KV/mm,25℃>20Flame resistance, UL 94V-0\Temperature range ,  ℃-40～120-40～120Volume resistance DC500V, Ω·cm1.2×1015Note：①All data above were tested under standardized condition.②All data listed in the chart were for the generalized item in the series; please refer to the related datasheet for special items.③Storage condition has a direct impact to the products’ shelf life, Please refer to the instruction for special items’ storing◆Operation1.Stirring A component evenly before using it .2.Weighed in a 5:1 ratio A, B two components, stir well stay with after vacuum deaeration to use within 60 minutes run out.3.Good potting devices ,if necessary, continue to pumping vacuum, help to increase the electrical performance of the device.4.Curing conditions: 25 ° C for 24hrs at room temperature ; or let stand for surface bubbles after heating 65 ℃ × 0.5hr.5.Note: adhesive start the reaction after adhesive preparation , accompanied by heat release. With the greater amount of glue, the greater the heat release, the shorter operating time, required in a shorter period of time you are finished using 6.The above tests are measured under 100 g with adhesive.◆Package and StoragePackage                                     Part A : Black , 25kg/bucket                            White, 25kg/bucket                 Part B: Black, 5kg/pot                                 White: 5kg/potStorageSeal and Avoid light and lightTemperature≤25℃, humidity≤50%RHShelf life: Part A 12months, Part B 12months◆Safety Operation MaterialMSDS isn't included here. Please read TDS, MSDS and label carefully before operation.You can get MSDS from Sepuna or other distributors, or mail to service center [email protected], or call +86-400-882-1323.◆Product WarrantyAll product properties and application details based on information believe to be reliable and accurate. But you still need to test its property and safety before application. The advices we supply don't apply in any circumstances. Sepuna don't make assurance of any other applications outside the specification until Sepuna supply a special written guarantee. Sepuna is only responsible to replace or refund if this product is defective within the warranty period stated above. Sepuna makes it clear that will not be liable of any accidents.